🚀Join Free - List Your Products & Reach Verified Global BuyersSign Up Free →
🚀List Your Products, Reach Global BuyersJoin Free

EN590 Dip and Pay Procedure: How It Works and Where It Fails

  • Published on : 18/11/2026
  • |
  • Last Updated on : 18/11/2026
EN590 Dip and Pay Procedure: How It Works and Where It Fails
B2B

Key takeaways

  • The EN590 dip and pay procedure releases the buyer's MT103 payment only after an independent inspector confirms on-site manifold samples meet EN590:2022 specifications at the load port.
  • Spot cargoes trade under dip and pay terms to bridge trust gaps between unfamiliar counterparties where cargoes change hands multiple times before loading.
  • The four-step transaction timeline covers LOI and ICPO exchange, SPA execution with dip test protocol, vessel nomination and inspector appointment, and on-site dip test triggering MT103 release.
  • Typical transactions range from 30,000 to 100,000 metric tonnes for Suezmax or Aframax parcels in Rotterdam, Fujairah, and Gibraltar spot markets.
  • Sellers prefer dip and pay because funds arrive within 24 to 48 hours of a passed test versus five to seven banking days for traditional letter of credit examination.
  • Pre-trade compliance requires a full KYC pack, notarized mandate letters, Irrevocable Corporate Purchase Order, and Banking Capability Letter verified via SWIFT BIC before SPA drafting.
  • The SPA dip and pay clause must name the approved inspector panel, ASTM test methods for density, sulfur, flash point, and distillation, and a hard MT103 release deadline typically within 24 banking hours.
  • Contractual guarantees routinely exceed EN590:2022 limits such as sulfur at 9.5 mg/kg max versus the 10.0 mg/kg regulatory maximum to create a quality buffer for on-site testing.
  • On-site dip testing follows ASTM D4057 and ISO 3170 sampling standards analyzing density, flash point, sulfur, water, and FAME content with portable ISO 17025 accredited equipment.
  • The buyer appoints and pays the independent inspector such as SGS or Intertek with fees ranging from four thousand to seven thousand US dollars for a standard Aframax cargo.

The EN590 dip and pay procedure is the dominant payment mechanism for spot diesel cargoes moving from the Middle East to Europe where 22.9 million metric tonnes traded in 2024 according to S&P Global Commodity Insights. It solves a specific trust problem: spot barrels often change hands multiple times before loading so sellers need payment tied to verified quality not just shipping documents. This article explains the exact four-step workflow from LOI exchange through on-site manifold testing to MT103 release, the contractual clauses that prevent disputes, the tighter-than-spec guarantees buyers demand, and the compliance checks that filter out fake mandates before they stall a deal.

You will learn how the dip test triggers payment within hours instead of days, why contractual limits for sulfur density and flash point are set stricter than the EN590:2022 standard, what the inspector actually measures on board using portable analyzers, and which document gaps cause the most delays during the KYC and mandate verification phase. The guide covers the full timeline, the payment mechanics behind MT760 SBLC and MT103 triggers, and the practical failure points where transactions collapse after the cargo is already loaded.

What Is EN590 Dip and Pay? Definition and Scope

The EN590 dip and pay procedure is a spot-market payment mechanism where the buyer releases funds only after an independent inspector confirms the cargo meets EN590:2022 specifications through on-site dip testing at the load port. This workflow exists because spot cargoes often change hands multiple times before loading and sellers need assurance that payment follows verified quality rather than documentary presentation alone. Unlike traditional documentary credits where banks release payment against shipping documents, dip and pay ties the MT103 release directly to a physical quality check performed at the vessel manifold. Middle East diesel exports to Europe rose to 22.9 million mt in 2024, making the region Europe's top supplier according to S&P Global Commodity Insights, and a significant portion of these spot barrels trade under dip and pay terms to bridge trust gaps between unfamiliar counterparties.

Core mechanics: on-site dip test triggers payment release

The core mechanic relies on a pre-agreed inspector boarding the vessel after loading commences, drawing manifold samples, and testing key parameters such as density, sulfur content, flash point, and distillation recovery on-site using portable analyzers. If results fall within EN590:2022 limits the inspector issues a pass certificate and the buyer's bank releases the MT103 within hours. The seller typically provides a fresh Notice of Readiness and the buyer nominates the inspector from an approved list such as SGS, Intertek, or Saybolt. This mechanism shifts the payment trigger from document handover to physical verification reducing the risk of paying for off-spec cargo that would later fail laboratory analysis.

Why sellers prefer dip and pay for spot cargoes

Sellers prefer dip and pay for spot cargoes because it accelerates cash flow compared to traditional LC terms that require full document sets and bank examination periods often lasting five to seven banking days. With dip and pay the seller receives funds within twenty-four to forty-eight hours of a passed test without waiting for original bills of lading to reach the buyer's bank. This is critical for traders financing cargoes on short-term credit lines where every day of float costs money. The procedure also eliminates discrepancies that commonly stall LC payments such as minor description mismatches or late document presentation.

Typical transaction size and market context

Typical dip and pay transactions range from 30,000 to 100,000 metric tonnes for Suezmax or Aframax parcels though smaller Handymax lots of 15,000 to 25,000 metric tonnes also appear in the Mediterranean and ARA markets. The procedure dominates spot trading in Rotterdam, Fujairah, and Gibraltar where cargoes trade on a prompt loading basis and counterparties often lack established credit lines. Buyers include independent storage operators, blending terminals, and regional distributors who need flexible procurement without long-term offtake commitments. The mechanism is rarely used for term contracts where quality history and credit trust allow standard documentary payment.

Step-by-Step EN590 Dip and Pay Transaction Timeline

The exact EN590 dip and pay procedure step by step follows a numbered sequence from initial offer to final payment release. Each stage has defined document exchanges, inspection appointments, and banking triggers that must align to avoid disputes. The timeline below captures the critical path for a standard FOB Rotterdam or CIF Mediterranean transaction.

StepActionKey DocumentsTypical DurationResponsible Party
1LOI and ICPO exchange with mandate verificationLOI, ICPO, BCL, Mandate Letter1-2 daysBuyer, Seller, Mandates
2SPA execution with dip and pay clause and Incoterms 2020Signed SPA, Appendix 1 Dip Test Protocol2-3 daysBuyer, Seller Legal
3Vessel nomination, NOR, and inspector appointmentVessel Q88, NOR, Inspector Confirmation3-5 daysSeller, Buyer
4On-site dip test, results, and MT103 triggerDip Test Certificate, CoQ, MT103 Release4-8 hoursInspector, Buyer Bank

The table shows the four critical phases each with distinct document requirements and time windows. Step one establishes counterparty legitimacy through the Letter of Intent, Irrevocable Corporate Purchase Order, and Banking Capability Letter while mandate letters confirm authority to bind principals. Step two locks commercial terms including the dip and pay clause, Incoterms 2020 selection, and the detailed sampling protocol in Appendix 1. Step three coordinates physical logistics where the seller nominates a vetted vessel, tenders Notice of Readiness, and both parties agree on an inspector from the approved panel. Step four executes the quality verification and payment release within a single port call window.

1. LOI and ICPO exchange with mandate verification

The LOI and ICPO exchange with mandate verification initiates the transaction by confirming both parties have authority and financial capacity. The buyer issues an Irrevocable Corporate Purchase Order on company letterhead specifying product grade, quantity, Incoterms, and the dip and pay payment clause. The seller responds with a Letter of Intent confirming allocation availability. Both sides exchange Banking Capability Letters from their respective banks confirming ability to issue or receive the payment instrument. Mandate letters must be notarized and include board resolutions when intermediaries represent end-buyers or title holders. Any gap in this chain stalls the SPA negotiation.

2. SPA execution with dip and pay clause and Incoterms 2020

SPA execution with dip and pay clause and Incoterms 2020 formalizes the commercial agreement and defines the exact testing parameters that trigger payment. The contract specifies EN590:2022 as the governing specification, the approved inspector panel, the sampling points at vessel manifold, and the pass or fail thresholds for each tested parameter. It also defines the MT103 release timeline typically within four banking hours of a passed dip certificate. Incoterms 2020 selection determines risk transfer FOB shifts risk at the vessel rail while CIF extends seller responsibility to the discharge port. The SPA appendix must list the exact portable analyzer models accepted for on-site testing.

3. Vessel nomination, NOR, and inspector appointment

Vessel nomination, NOR, and inspector appointment align physical availability with inspection capacity. The seller provides the vessel Q88 questionnaire detailing tank cleaning history, previous cargoes, and class certification. Upon vessel arrival at the load port the seller tenders Notice of Readiness stating the vessel is ready to load. The buyer confirms the inspector from the SPA approved list and the inspector boards to witness loading and draw manifold samples. Delays in NOR acceptance or inspector availability directly extend the timeline and may trigger demurrage clauses.

4. On-site dip test, results, and MT103 trigger

On-site dip test, results, and MT103 trigger complete the transaction when the inspector tests manifold samples for density at 15°C, sulfur content, flash point, and distillation recovery. Results are compared against EN590:2022 limits in real time. A pass certificate authorizes the buyer's bank to release the MT103 to the seller's account. If any parameter fails the cargo is rejected or re-test rights are invoked per the SPA. The seller receives funds before the vessel sails eliminating post-loading payment risk. The full documentation package follows by courier for the buyer's customs clearance.

Pre-Trade Compliance: KYC, ICPO, BCL, and Mandate Verification

Verification starts with a complete KYC pack for both counterparties before any SPA is drafted. The buyer must provide a certificate of incorporation, memorandum and articles of association, board resolution authorizing the signatory, and a bank reference letter confirming creditworthiness. The seller mirrors this with corporate documents, refinery or terminal allocation letters, and a valid export license. Both sides submit passport copies of authorized signatories and a signed non-disclosure agreement. Missing or expired documents stall the process and signal potential shell companies. Global Trade Plaza members can display a verified badge that accelerates this step by confirming baseline corporate vetting has occurred.

KYC pack requirements for buyer and seller

KYC pack requirements for buyer and seller include corporate registration certificates, board resolutions, bank references, and authorized signatory identification. The buyer adds a recent audited financial statement or a bank comfort letter (BCL) confirming the ability to issue the payment instrument. The seller provides the refinery commitment letter or terminal storage receipt proving title to the EN590 cargo. Both parties exchange these documents through secure data rooms or encrypted email before the mandate is accepted. Incomplete packs are the primary cause of delays during the compliance window.

Validating ICPO, BCL, and Proof of Product (POP)

Validating ICPO, BCL, and Proof of Product (POP) requires cross-referencing the issuing bank's SWIFT address and confirming the instrument is irrevocable and unconditional. The irrevocable corporate purchase order (ICPO) must state the exact EN590:2022 specification, quantity in metric tons, Incoterm, load port, and laycan dates. The BCL references the buyer's bank officer by name, direct line, and SWIFT BIC for verification calls. POP from the seller includes the tank farm storage receipt, the most recent independent quality and quantity (Q&Q) report, and the injection report showing the product meets the minimum cetane number of 51.0 according to DieselNet. Any discrepancy between the ICPO terms and the POP voids the mandate.

Spotting fake mandates and circular mandate chains

Spotting fake mandates and circular mandate chains begins with demanding a direct mandate letter from the principal on company letterhead, notarized and apostilled where required. The letter must name the specific intermediary, the transaction scope, and a validity period not exceeding 30 days. Intermediaries who cannot produce this letter or who present a chain of three or more mandates are typically recycling the same offer. Verify the principal's contact details independently through the chamber of commerce or the refinery's commercial department. Refuse to engage if the mandate holder insists on "soft probe" procedures or requests the seller's tank farm details before signing an NDA.

Contractual Framework: SPA Terms, Incoterms 2020, and EN590:2022 Specs

The sales and purchase agreement (SPA) anchors every dip and pay transaction with binding payment triggers, quality warranties, and risk allocation. The dip and pay clause must state that the buyer's bank releases the MT103 within a defined number of banking hours after the inspector issues the pass certificate. It specifies the approved inspector list, the re-test procedure, and the exact EN590:2022 parameters that constitute a pass. Force majeure, demurrage rates, and governing law clauses complete the framework. Ambiguity in any of these terms creates payment disputes after the cargo is loaded.

Essential dip and pay clause wording and payment triggers

Essential dip and pay clause wording and payment triggers define the precise moment the buyer's obligation becomes unconditional. The clause names the inspector, the test methods (ASTM D4052 for density, ASTM D2622 for sulfur, ASTM D93 for flash point, ASTM D86 for distillation), and the pass/fail thresholds. It states that a pass certificate transmitted by the inspector's official email to both parties' banks authorizes the MT103 release. The clause also sets a hard deadline, typically 24 banking hours, for the buyer's bank to execute the transfer. Failure to release funds within this window constitutes a buyer default under the SPA.

FOB vs CIF risk transfer during dip testing

FOB vs CIF risk transfer during dip testing determines who bears the cost of a failed cargo at the manifold. Under FOB the seller arranges and pays for the inspector at the load port; risk passes to the buyer once the product crosses the ship's rail after a passed dip test. Under CIF the seller also covers freight and insurance to the discharge port but the dip test still occurs at the load port manifold. If the cargo fails on-site the seller retains title and risk under both terms. The SPA must clarify who pays for the inspector's re-attendance if a re-test is invoked. This distinction drives the cost structure in the commercial offer.

Table: EN590:2022 spec limits vs typical contractual guarantees

ParameterEN590:2022 LimitTypical Contractual GuaranteeTest MethodRe-test Tolerance
Density at 15°C820 - 845 kg/m³825 - 840 kg/m³ASTM D4052 / ISO 12185±0.5 kg/m³
Flash point55 °C min58 °C minASTM D93 / ISO 2719±1 °C
Distillation 95% recovered360 °C max355 °C maxASTM D86 / ISO 3405±2 °C

The table shows that contractual guarantees are routinely tighter than the EN590:2022 standard to build a quality buffer for the dip test. Sulfur is guaranteed at 9.5 mg/kg against the 10.0 mg/kg regulatory maximum according to DieselNet (current standard). Cetane number is guaranteed at 52.0 min against the 51.0 min regulatory minimum according to DieselNet (current standard). Density, flash point, and 95 percent distillation recovery all carry stricter minima or maxima. Re-test tolerances reflect the repeatability limits of the cited test methods. Buyers should insist on these tightened guarantees in the SPA to reduce the probability of a marginal fail that triggers costly demurrage and re-test cycles. For deeper specification details see the EN590 10 ppm diesel specifications and global uses guide.

On-Site Dip Testing Protocol: Sampling Standards and Inspector Roles

ASTM D4057 and ISO 3170 sampling standards

The EN590 dip test follows ASTM D4057 for manual sampling and ISO 3170 for automatic pipeline sampling to ensure the composite sample represents the entire cargo. The inspector draws upper middle and lower samples from each tank compartment after a minimum settling period of thirty minutes. These spot samples are combined proportionally by volume into a composite which is then homogenized before subsamples are distributed to the buyer laboratory the seller laboratory and the independent inspector laboratory. Any deviation from the prescribed sampling height or mixing procedure invalidates the dip test and forces a re-sample which adds twenty four to forty eight hours to the vessel schedule.

On-site parameters: density flash point sulfur water FAME

The portable laboratory analyzes five critical parameters on site. Density at fifteen degrees Celsius is measured with a digital density meter following ASTM D4052. Flash point uses a Pensky Martens closed cup tester per ASTM D93. Sulfur content is determined by X ray fluorescence per ASTM D2622 or ISO 20846. Water content is checked by Karl Fischer titration and FAME content by infrared spectroscopy. EN 590 allows a FAME (biodiesel) content of 7% according to DieselNet (EN 590:2009 onward). Results must fall within the contractual tolerances which are tighter than the EN590:2022 standard limits to create a quality buffer.

Inspector appointment costs and report turnaround time

The buyer typically appoints and pays for the independent inspector such as SGS Intertek or Bureau Veritas. Inspection fees for a standard Aframax cargo range from four thousand to seven thousand US dollars depending on port location and laboratory mobilization distance. The inspector issues a provisional Certificate of Quality within four to six hours of sampling completion. The final signed report with all five parameter results is delivered within twelve to twenty four hours. The SPA should specify that the inspector acts as the sole arbiter for dip test pass or fail to prevent disputes over marginal results.

ParameterTest MethodTypical On-Site LimitRe-test ToleranceEquipment Type
Density at 15°CASTM D4052 / ISO 12185825 - 840 kg/m³±0.5 kg/m³Digital density meter
Flash pointASTM D93 / ISO 271958 °C min±1 °CPensky-Martens closed cup
Sulfur contentASTM D2622 / ISO 208469.5 mg/kg max±0.3 mg/kgX-ray fluorescence
Water contentASTM D6304 / ISO 12937200 mg/kg max±10 mg/kgKarl Fischer titration

The table summarizes the five on-site dip test parameters with their standard test methods contractual limits and re-test tolerances. Density and flash point provide immediate physical property verification while sulfur and FAME confirm regulatory compliance. Water content detects contamination from ballast or tank bottoms. The re-test tolerance column reflects the repeatability of each instrument and determines whether a marginal fail triggers an automatic re-run or a formal dispute. Buyers should verify that the inspector's portable laboratory holds current ISO 17025 accreditation for each method listed.

Payment Mechanics: MT760 SBLC DLC and MT103 Release Triggers

MT760 SBLC blocking funds for 10ppm ULSD cargo value

The MT760 SWIFT message transmits a Standby Letter of Credit from the buyer bank to the seller bank blocking the full cargo value for the duration of the voyage plus a grace period of fifteen to thirty days. The SBLC is typically issued to cover potential price adjustments or demurrage. It must be irrevocable confirmed by a prime international bank and callable on first demand with a simple statement that the dip test has passed and shipping documents have been presented. The seller bank authenticates the MT760 via RMA keys before advising the beneficiary.

DLC MT700 structure and dip test presentation terms

A Documentary Letter of Credit issued via MT700 replaces the SBLC in many CIF transactions. The DLC lists the full document set required for payment including the Bill of Lading commercial invoice packing list Certificate of Origin Certificate of Quality Quantity and Quality report Notice of Readiness and the independent inspector dip test report. The critical clause states that payment is triggered only upon presentation of a passed dip test report showing all five parameters within contractual limits. Any discrepancy in the dip test report such as a missing parameter or an expired inspector accreditation allows the issuing bank to refuse payment until a clean presentation is made.

MT103 release workflow after passed dip test

Once the independent inspector emails the provisional passed dip test report the seller presents the full document package to the negotiating bank. The negotiating bank checks documents against the DLC terms within five banking days. If compliant the negotiating bank sends documents to the issuing bank via SWIFT MT700 series messages. The issuing bank has a maximum of five banking days to examine and authorize payment. The MT103 single customer credit transfer is then released to the seller account typically within two banking days after issuing bank acceptance. The total workflow from passed dip test to funds in seller account averages seven to twelve banking days.

InstrumentSWIFT TypeTypical CoverageValidity PeriodPayment TriggerBank Charges (approx.)
SBLCMT760Cargo value plus contingencyVoyage + 30 daysPassed dip test + docs1.0-1.5% p.a.
DLCMT700Invoice valueLatest shipment + 21 daysPassed dip test + clean docs0.15-0.25% flat
MT103MT103Final settlementImmediateIssuing bank acceptance: see official tariff-75 per transfer

The table compares the three payment instruments used in EN590 dip and pay transactions. The SBLC via MT760 provides the seller with a bank guarantee independent of document discrepancies but carries higher annual fees. The DLC via MT700 ties payment directly to document compliance including the dip test report and is cheaper but exposes the seller to refusal risk for minor discrepancies. The MT103 is the final settlement wire executed only after the issuing bank accepts the presentation. Buyers should ensure the SBLC or DLC expiry date extends at least thirty days beyond the estimated arrival date to cover demurrage or re-test delays.

Top 10 Red Flags and Scam Patterns in EN590 Spot Markets

Soft offers without verifiable POP or tank farm receipts

A legitimate EN590 supplier provides a verifiable Proof of Product (POP) that includes a tank farm receipt, a fresh Certificate of Quality (CoQ) from an accredited inspector, and a tank storage agreement (TSA) matching the seller’s name. Scammers circulate soft offers with only a generic product passport or a CoQ dated months earlier. Buyers must demand a live video call from the tank farm showing the tank number, volume, and seal numbers matching the TSA. Any refusal to share the TSA or to allow an independent inspector to verify ullage before signing the SPA is a primary indicator that the product does not exist or is double-sold.

Fake SGS/Intertek certificates and photoshopped dip reports

Fraudsters frequently forge certificates from major inspectors such as SGS, Intertek, or Saybolt by altering PDF metadata, swapping vessel names, or changing sulfur and density figures. Authentic certificates carry a unique verification QR code or a reference number searchable on the inspector’s public verification portal. Buyers should never accept a certificate sent only by email from the seller’s representative. Instead, request the inspector’s direct contact details and verify the report independently through the official portal. A dip test report that lacks the inspector’s wet-ink signature, the jointly sealed sample receipt, or the vessel’s NOR timestamp is inadmissible for payment release.

Upfront fee demands for SBLC issuance or inspector travel

No credible seller or mandate requires the buyer to pay upfront fees for SBLC issuance, inspector travel, or “logistics coordination” before the dip test. The standard dip-and-pay model places the cost of the inspector on the seller or splits it per the SPA, with payment triggered only after a passed dip test. Requests for payment to a third-party consultant, a “facilitator” wallet, or a non-bank account for SWIFT charges are hallmarks of advance-fee fraud. Banks issue SBLCs or DLCs based on the buyer’s credit line, not on fees paid to the seller. Any party insisting on crypto, Western Union, or payments to individuals rather than corporate accounts should be treated as a scam.

Trade Diesel & EN590 on Global Trade Plaza: diesel on Global Trade Plaza, diesel suppliers and exporters, diesel buyers and importers, en 590 10 ppm diesel, diesel fuel en590 buy requirement, automotive gas oil, petroleum oil related products on Global Trade Plaza, diesel fuel en590 euro 5 10ppm netherlands, diesel fuel en590 usdl 10 ppm, en590 diesel 10ppm ulsd, marine fuel gas oil mgo, diesel fuel en 590 ulsd 10 ppm ulsd 50ppm.

Conclusion: Executing EN590 Dip and Pay with Confidence

A successful EN590 dip and pay transaction relies on three pillars: a watertight SPA that defines every trigger and tolerance, pre-vetted banking instruments that eliminate payment ambiguity, and an independent inspector whose sampling protocol leaves no room for dispute. Buyers must issue ICPOs and BCIs that match the seller’s mandate exactly, while sellers must ensure the product in the shore tank matches the CoQ specifications before NOR is tendered. The inspection window is the single point of failure; weather delays, lab queues, and bank compliance holds are predictable risks that a long-stop date clause neutralizes. Using verified counterparties found through established channels such as industry associations, major energy trade shows, or platforms like Global Trade Plaza reduces the probability of documentation fraud. Treat the dip test as a binary gate: if the cargo passes, payment releases automatically; if it fails, the contract dictates the remedy without renegotiation. Discipline on both sides of the trade turns a high-risk spot deal into a repeatable, financeable operation.

Frequently Asked Questions

What is the exact EN590 dip and pay procedure step by step?

The procedure follows four steps: LOI and ICPO exchange with mandate verification, SPA execution with dip test protocol, vessel nomination and inspector appointment, and on-site manifold testing triggering MT103 release. The inspector boards at the load port, draws samples per ASTM D4057, tests key parameters, and issues a pass certificate. The buyer's bank then releases funds within the contractual window, typically 24 banking hours.

Which bank instruments are standard for EN590 dip and pay (MT760, DLC, SBLC)?

The standard instrument is an MT103 wire transfer released after the dip test passes. MT760 SBLCs or DLCs are occasionally used as pre-instruments to prove buyer capability during KYC but are not the payment trigger. The SPA defines the MT103 as the sole settlement method to avoid LC document examination delays.

What happens if the dip test fails EN590 10ppm sulfur specs?

The cargo is rejected at the load port and the seller must replace it or cancel the transaction without payment release. The SPA typically grants one re-test right using a retained sample if the initial failure is marginal. If the re-test fails, the seller bears demurrage and any price differential for replacement barrels.

Who pays for the SGS/Intertek inspector at the load port?

The buyer appoints and pays the independent inspector such as SGS or Intertek. Fees range from four thousand to seven thousand US dollars for a standard Aframax cargo covering travel, boarding, and portable analyzer deployment. The cost is a buyer expense because they select the inspector from the SPA approved panel.

Can the buyer reject cargo after a passed dip test but failed lab report?

No, a passed dip test certificate is final and triggers the irrevocable MT103 release per the SPA. The dip and pay mechanism replaces the final lab report as the payment trigger to eliminate post-loading disputes. Contractual guarantees are set stricter than EN590:2022 limits to create a buffer against lab variance.

What is the difference between FOB and CIF dip and pay risk?

Under FOB the buyer bears risk once cargo passes the vessel rail at the load port so the dip test occurs before risk transfer. Under CIF the seller retains risk to the discharge port but the dip test still occurs at loading; a pass certificate releases payment while the seller manages freight and insurance separately.

How long does the dip test and payment release take?

The on-site dip test and results take four to eight hours once the inspector boards the vessel. The buyer's bank releases the MT103 within the contractual deadline, typically four to twenty-four banking hours after receiving the pass certificate. Funds reach the seller's account before the vessel sails.

What POP documents prove the EN590 cargo exists?

Proof of Product includes the refinery allocation letter, tank farm storage receipt, fresh Notice of Readiness, and the vessel Q88 questionnaire. The Q88 details tank cleaning history and class certification confirming the vessel is suitable for EN590 grade diesel. These documents are verified during KYC before SPA execution.

Is a dip and pay clause legally binding in an SPA?

Yes, the dip and pay clause is a binding condition precedent to payment in the Sale and Purchase Agreement. It defines the inspector panel, sampling standards ASTM D4057 and ISO 3170, pass/fail thresholds, and the MT103 release timeline. Courts uphold these clauses as they replace documentary conditions with physical verification.

What are the common mandate chain scams in EN590 trading?

Common scams involve fake mandates claiming authority without board resolutions, shell companies issuing ICPOs without financial capacity, and intermediaries circulating the same cargo offer to multiple buyers. Verification requires notarized mandate letters, board resolutions, and a Banking Capability Letter confirmed via SWIFT BIC before SPA drafting.

What sampling standards apply to EN590 dip testing (ASTM D4057, ISO 3170)?

On-site dip testing follows ASTM D4057 for manual sampling and ISO 3170 for automatic pipeline sampling at the vessel manifold. The inspector uses portable ISO 17025 accredited analyzers to test density at 15°C, sulfur, flash point, distillation recovery, water content, and FAME. The SPA appendix lists accepted analyzer models.

How are price renegotiations calculated for off-spec EN590 cargo?

Price renegotiations are rare because the dip test is a pass/fail gate not a quality adjustment mechanism. If the SPA allows a claim for off-spec cargo discovered post-loading, the discount references the Platts FOB Rotterdam or Med benchmark minus freight and a penalty margin. Most SPAs reject cargo outright rather than renegotiate.

Sources

Tags

  • #en590 dip and pay

About Author

Author Name : Global Trade Plaza
Bio : Global Trade Plaza is a verified B2B marketplace connecting exporters, importers, wholesalers, and manufacturers worldwide. Our team writes practical guides on international trade, sourcing, and compliance, drawing on daily work with verified businesses across 50+ countries.
Reviewed by : Ankit Singh, Trade Content Expert at Global Trade Plaza
Ankit reviews sourcing and supplier-verification content at Global Trade Plaza, focusing on how buyers assess exporters across South and Southeast Asia.